Lýsing
Treat yourself to the best. The Epix+ series stands out from the crowd with a proprietary, sporty design, developed with today’s modern vehicles in mind. The EPIX5+ Work Strobe is a work light ramp with selectable red and yellow/orange position light and approved R65 flash light that ensures your visibility. The unique position light is fully integrated into the reflector. In addition, the ramp is approved as both a reversing light and a taillight according to ECE R23 and R148.
The EPIX5+ Work Strobe is the work light ramp that gives a modern look and has the performance to meet all situations. With its 30 W, this ramp provides a working light with a range of 59m at 1 lux and a wide 120° light pattern so you get maximum light over a large area. With 1700 actual lumens and a color temperature of 5000K, it provides strong and natural lighting that facilitates work in all conditions. Self-developed smart mounts ensure mounting pretty much wherever and however you want on the vehicle.
Position light
The ramp has the Epix series specially designed reflectors, which are fully integrated into the reflector. The color of the position light can also be selected between yellow/orange and red, which is also approved.
Flash light
The Epix5+ Work Strobe is equipped with 10 different flash light patterns, one of which is ECE R65 approved. By simply connecting two units together, you can get both synchronous and asynchronous flash patterns between them. Use your Epix5+ Work Strobe LED ramp as a work light or reversing light; the strobe turns off when switched on and then starts with your previously selected flash pattern immediately when you then turn off the working light again.
What else is needed?
- DT relay kit: Ledson Connect provides a super easy connection while being interconnectable if there is a future desire to easily expand with additional lights or ramps
- If you want to lower the energy consumption of your Epix Work Series work ramp, you can easily install our E-screw . By mounting this screw on the back of the ramp, it is put into eco mode, the brightness is lowered and energy consumption is reduced.
Characteristics and technical data:
- Approved as: reversing light and taillight with approved flashing light
- E-marked ECE R148 (R1, SM1), R23, R65 and R10 (EMC rated)
- Position light, integrated in the reflector
- Selectable position light in red or yellow/orange
- 120° diffuse light pattern (wide light)
- Range: 59 m (1 lux)
- 2,450 lumens (theoretical), 1,700 lumens (actual)
- Color temperature 5000K (Neutral white)
- 30 W (2 x 15 W LEDs)
- Voltage: 9-36V
- IP69K (water/dustproof)
- Aluminum housing and polycarbonate lens
- Side reflective optics
- Pressure equalization membrane
- Electronic heat management
- DT connector (supplied)
- 1.8 at 12V (3.6A in eco mode) and 0.9 at 24V (1.7A in eco mode) (calculate eco mode? Wrong)
Included:
- EPIX5+ Work Strobe LED Ramp
- Bolts and screws to attach the ramp to the appropriate surface
- Mounting details for gable mounting
- Mounting details for rear mounting, standing/hanging
- DT connector 6-pin
Dimensions (excl. brackets):
- Width: 128 mm
- Height: 43 mm
- Depth: 61 mm
Flash light pattern
- Single flash synchronized: 2.2 Hz
- Single flash asynchronous: 2.2 Hz (when using 2 ramps)
- Triple flash synchronized: 1.1 Hz
- Triple flash asynchronous: 1.1 Hz (when using 2 ramps)
- Quadruple flash synchronized: 1.25 Hz
- Quadruple flash asynchronous: 1.25 Hz (when using 2 ramps)
- Combination (one long and five short) synchronized: 0.83 Hz
- Combination (one long and five short) asynchronous: 0.83 Hz (when using 2 ramps)
- Flash burst synchronized: 10 Hz
- Flash series asynchronous: 10 Hz (when using 2 ramps)
NOTE: The DT connector must not be cut as this means an increased risk of moisture damage and the warranty then ceases to apply.
